#HF     .Run processes and interact with them in reflexNone&'>XEreflex-processThe output of a processreflex-processFires whenever there's some new stdout output. Depending on the buffering strategy of the implementation, this could be anything from whole lines to individual characters.reflex-process;Fires whenever there's some new stderr output. See note on .reflex-process&Fires when the process is over and no stdout or stderr* data is left. Once this fires, no other "s for the process will fire again.reflex-process?Fires when a signal has actually been sent to the process (via  ).reflex-processThe inputs to a process reflex-processstdin input to be fed to the process reflex-processSignals to send to the process reflex-process/A message that's sent to the underlying process reflex-process%Send an EOF to the underlying processreflex-processSend the last message (an EOF will be added). This option is offered for convenience, because it has the same effect of sending a Message and then the EOF signalreflex-process A default  where stdin and signals are never sent.You can also use .reflex-process+Create a process feeding it input using an  and exposing its output 9s representing the process exit code, stdout, and stderr.The stdout and stderr s are line-buffered.]N.B. The process input is buffered with an unbounded channel! For more control of this, use  directly. N.B.: The , , and  parameters of the provided J are replaced with new pipes and all output is redirected to those pipes.reflex-process+Create a process feeding it input using an  and exposing its output with s for its exit code, stdout, and stderrV. The input is fed via a buffer represented by a reading action and a writing action.The stdout and stderr s are line-buffered.For example, you may use Chan for an unbounded buffer (like  does) like this: > channel <- liftIO newChan > createProcessBufferingInput (readChan channel) (writeChan channel) myConfigSimilarly you could use TChan.JBounded buffers may cause the Reflex network to block when you trigger an ; that would cause more data to be sent to a process whose stdin is blocked.If an unbounded channel would lead to too much memory usage you will want to consider * speeding up the consuming process. * buffering with the file system or another persistent storage to reduce memory usage. * if your usa case allows, dropping $s or messages that aren't important. N.B.: The , , and  parameters of the provided J are replaced with new pipes and all output is redirected to those pipes.reflex-processRuns a process and uses the given input and output handler functions to interact with the process via the standard streams. Used to implement . N.B.: The , , and  parameters of the provided J are replaced with new pipes and all output is redirected to those pipes.reflex-process"Specification of process to createreflex-process*Reflex-level configuration for the processreflex-processrAn action that reads a value from the input stream buffer. This must block when the buffer is empty or not ready.reflex-process9An action that writes a value to the input stream buffer.reflex-process"Specification of process to createreflex-process*Reflex-level configuration for the processreflex-process,Builder for the standard input handler. The " is the write end of the process' stdin and the resulting  i -> IO (): is a function that writes each input 'Event t i' to into H. This functios must not block or the entire Reflex network will block.reflex-process-Builder for the standard output handler. The ! is the read end of the process' stdout and the  o -> IO (), is a function that will trigger the output  Event t o when called. The resulting IO ()T will be run in a separate thread and must block until there is no more data in the  to process.reflex-process,Builder for the standard error handler. The ! is the read end of the process' stderr and the  e -> IO (), is a function that will trigger the output  Event t e when called. The resulting IO ()T will be run in a separate thread and must block until there is no more data in the  to process.reflex-process"Specification of process to createreflex-process*Reflex-level configuration for the process        !"#$reflex-process-0.3.0.0-inplaceReflex.ProcessProcess_process_handle_process_stdout_process_stderr _process_exit_process_signal ProcessConfig_processConfig_stdin_processConfig_signalSendPipeSendPipe_Message SendPipe_EOFSendPipe_LastMessagedefProcessConfig createProcesscreateProcessBufferingInputunsafeCreateProcessWithHandlescreateRedirectedProcess$fDefaultProcessConfigOreflex-0.7.1.0-7f31a6b041c6dfb2617aacc8fb1c186150894a3bb6bf80b1786c6fe1dd732071 Reflex.ClassEvent[data-default-class-0.1.2.0-4272acf61cf305de58358a7df34113e19eeebed30a53e4d682ade7ae34d135e4Data.Default.ClassdefbaseGHC.IO.Handle.TypesHandleprocess-1.6.8.0System.Process.Commonstd_instd_outstd_err CreateProcess