streaming-commons-0.2.2.3: Common lower-level functions needed by various streaming data libraries
Safe HaskellNone
LanguageHaskell2010

Data.Streaming.ByteString.Builder

Description

Convert a stream of bytestring Builders into a stream of ByteStrings.

Adapted from blaze-builder-enumerator, written by Michael Snoyman and Simon Meier.

Note that the functions here can work in any monad built on top of IO or ST.

Also provides toByteStringIO* like Blaze.ByteString.Builders, for Data.ByteString.Builder.

Since 0.1.9

Synopsis

Documentation

type BuilderPopper = IO ByteString Source #

Provides a series of ByteStrings until empty, at which point it provides an empty ByteString.

Since 0.1.10.0

toByteStringIO

toByteStringIO :: (ByteString -> IO ()) -> Builder -> IO () Source #

Run the builder with a defaultChunkSized buffer and execute the given IO action whenever the buffer is full or gets flushed.

 toByteStringIO = toByteStringIOWith defaultChunkSize

Since 0.1.9

toByteStringIOWith Source #

Arguments

:: Int

Buffer size (upper bounds the number of bytes forced per call to the IO action).

-> (ByteString -> IO ())

IO action to execute per full buffer, which is referenced by a strict ByteString.

-> Builder

Builder to run.

-> IO () 

toByteStringIOWith bufSize io b runs the builder b with a buffer of at least the size bufSize and executes the IO action io whenever the buffer is full.

Compared to toLazyByteStringWith this function requires less allocation, as the output buffer is only allocated once at the start of the serialization and whenever something bigger than the current buffer size has to be copied into the buffer, which should happen very seldomly for the default buffer size of 32kb. Hence, the pressure on the garbage collector is reduced, which can be an advantage when building long sequences of bytes.

Since 0.1.9

toByteStringIOWithBuffer :: Int -> (ByteString -> IO ()) -> Builder -> ForeignPtr Word8 -> IO () Source #

Use a pre-existing buffer to toByteStringIOWith.

Since 0.1.9

Buffers

data Buffer Source #

A buffer Buffer fpbuf p0 op ope describes a buffer with the underlying byte array fpbuf..ope, the currently written slice p0..op and the free space op..ope.

Since 0.1.10.0

Status information

freeSize :: Buffer -> Int Source #

The size of the free space of the buffer.

Since 0.1.10.0

sliceSize :: Buffer -> Int Source #

The size of the written slice in the buffer.

Since 0.1.10.0

bufferSize :: Buffer -> Int Source #

The size of the whole byte array underlying the buffer.

Since 0.1.10.0

Creation and modification

allocBuffer :: Int -> IO Buffer Source #

allocBuffer size allocates a new buffer of size size.

Since 0.1.10.0

reuseBuffer :: Buffer -> Buffer Source #

Resets the beginning of the next slice and the next free byte such that the whole buffer can be filled again.

Since 0.1.10.0

nextSlice :: Int -> Buffer -> Maybe Buffer Source #

Move the beginning of the slice to the next free byte such that the remaining free space of the buffer can be filled further. This operation is safe and can be used to fill the remaining part of the buffer after a direct insertion of a bytestring or a flush.

Since 0.1.10.0

Conversion to bytestings

unsafeFreezeBuffer :: Buffer -> ByteString Source #

Convert the buffer to a bytestring. This operation is unsafe in the sense that created bytestring shares the underlying byte array with the buffer. Hence, depending on the later use of this buffer (e.g., if it gets reset and filled again) referential transparency may be lost.

Since 0.1.10.0

unsafeFreezeNonEmptyBuffer :: Buffer -> Maybe ByteString Source #

Convert a buffer to a non-empty bytestring. See unsafeFreezeBuffer for the explanation of why this operation may be unsafe.

Since 0.1.10.0

Buffer allocation strategies

type BufferAllocStrategy = (IO Buffer, Int -> Buffer -> IO (IO Buffer)) Source #

A buffer allocation strategy (buf0, nextBuf) specifies the initial buffer to use and how to compute a new buffer nextBuf minSize buf with at least size minSize from a filled buffer buf. The double nesting of the IO monad helps to ensure that the reference to the filled buffer buf is lost as soon as possible, but the new buffer doesn't have to be allocated too early.

Since 0.1.10.0

allNewBuffersStrategy :: Int -> BufferAllocStrategy Source #

The simplest buffer allocation strategy: whenever a buffer is requested, allocate a new one that is big enough for the next build step to execute.

NOTE that this allocation strategy may spill quite some memory upon direct insertion of a bytestring by the builder. Thats no problem for garbage collection, but it may lead to unreasonably high memory consumption in special circumstances.

Since 0.1.10.0

reuseBufferStrategy :: IO Buffer -> BufferAllocStrategy Source #

An unsafe, but possibly more efficient buffer allocation strategy: reuse the buffer, if it is big enough for the next build step to execute.

Since 0.1.10.0